Description

Original 44mm rinse aid compartment cover gasket for Miele dishwasher Miele 6082322

The original Miele 6082322 rinse aid compartment cover seal is the small rubber part that prevents the leakage of rinse aid (Rinse Aid) from the integrated dispenser in your dishwasher. The 44mm diameter seal fits models G1xxx to G6xxx and restores the rinse aid cartridge to a full seal. A genuine Miele part that ensures a precise fit and a long service life.

Is the rinse aid cartridge in your Miele dishwasher emptying too quickly? This is the most common reason – the 44 mm rubber seal that seals the cartridge lid wears out over time and loses its elasticity. The result: rinse aid leaks into the dosing tube instead of being released at the right time and in the right amount.

Before ordering – safety first! To ensure a successful repair and maintain the performance of your dishwasher, it is essential to use only genuine Miele parts. Non-genuine parts may not fit the exact dimensions and cause a continuous leak. Now click the 'Check Model Compatibility' button at the top of the page – our system will immediately confirm that the part is suitable for you.

Why does the rinse aid cartridge empty quickly?

The gasket that seals the lid of the rinse aid dispenser is a small rubber part that is exposed to heat and chemicals with every wash cycle. After years of use, it loses its elasticity and hardens – and then stops sealing properly. Rinse aid leaks into the rinse compartment instead of staying in the dispenser until it’s time to be released. The most obvious sign: rinse aid that runs out in 3-4 cycles instead of dozens of cycles.

✅ Original Miele part guarantees:

• Food-grade rubber that withstands high wash temperatures
• Precise 44mm diameter – no need to “force-fit”
• Full sealing that returns the automatic dosing to normal operation

Location of the E-Nr sticker: On Miele dishwashers, the model sticker is located on the door edge – open the door and check the top or side interior.

📋 Technical specifications

✅ Compatible models

The part fits the following models (make sure it matches the E-Nr number on the sticker):

G1 Series: G1200, G1222, G1224, G1232, G1242, G1243, G1244, G1287, G1293 and all G1xxx models

G2 Series: All G2xxx models

G3 Series: All G3xxx models

G4 Series: All G4xxx models

G5 Series: All G5xxx models

G6 Series: All G6xxx models

🔧 How do you replace the flush cartridge seal?

Replacing the gasket is a simple DIY job – no tools required, and takes about 5 minutes. All you need to do is locate the integrated dosage on the inside of the dishwasher door and replace the old rubber with a new one.

Before replacing: ⚠️ Make sure the device is turned off.

Replacement steps:

1. Open the dishwasher door completely.
2. Locate the combined dosing unit – the plastic box on the inside of the door that contains both the detergent compartment and the round rinse aid cartridge.
3. Open the rinse aid cartridge lid (press the small button).
4. Remove the old rubber seal from the groove around the cartridge opening.
5. Place the new gasket 6082322 in the groove – press around the entire circumference until it is fully seated.
6. Close the lid and check that it closes without effort – a sign that the seal is properly secured.

💡 Tip: Before closing, fill the cartridge and check that the lid closes smoothly. If it closes with difficulty, the seal probably did not fully enter the groove.

💡 Tip from the experts

From the experience of our technicians, about 60% of calls about “fluid running out quickly” end with replacing just this seal – and not replacing the entire dosing unit. Before calling a technician for an inspection – it’s worth looking at the rubber seal: if it looks flat, hard, or not closed evenly across the circumference – that’s the sign. A 5-minute, 5-minute replacement saves a service visit. In addition: Higher amounts of fluid than necessary wear out the seal faster – check that the setting is set to level 2-3 and not 5-6.

❓ Frequently Asked Questions

What is the sign that the seal in the flushing cartridge is worn out?

The obvious sign is the rapid emptying of the rinse aid cartridge – instead of dozens of cycles, it empties in just 3-5 washes. Another sign: the rinse aid cartridge lid does not close properly, or you can see rinse aid residue around the opening. A simple test: press the rubber seal with your finger – if it is hard and inflexible, it needs to be replaced.

Do all Miele G1-G6 series dishwashers use this gasket?

Yes, the 6082322 gasket with a diameter of 44 mm is suitable for models G1xxx to G6xxx – dozens of models. It is important to verify the exact model number (E-Nr) from the sticker on the door edge before ordering, as some models may use a different dosage.

Can the seal be replaced without disassembling the dosing unit?

Yes – this is the strength of this replacement. The seal is directly accessible when you open the flush cartridge lid, and you don’t have to remove the dosing unit from the door. No tools are required. The replacement is suitable for anyone with 5 minutes and basic DIY skills.

What is the difference between an original part and a non-original part?

The original Miele part 6082322 is made of rubber in the exact 44 mm version, which is adapted to the sealing groove in the cartridge opening. Non-original parts may come in slightly different sizes - then the seal will not be complete. Result: the rinsing fluid will continue to leak even after the "repair". ⚠️ Using an unapproved part may cause long-term damage.