Description

Original lower left support rod for the Liebherr freezer drawer 7432348

The original Liebherr 7432348 lower left support rod is the structural part responsible for the stability of the freezer drawer on the lower left side. The part fits Liebherr K and KB series refrigerators and freezers, and restores full support to a drawer that is leaning, sliding diagonally, or has fallen to the left. An original part that ensures a precise fit and durability over the years.

About 60% of customers who come to us with a freezer drawer that “isn’t working properly” – discover that the problem is a broken support rod. The drawer doesn’t open straight, its left side drops, and it “drags” – these are all clear signs that the lower left support rod is cracked or broken. Replacing the part itself is simple and takes minutes.

A moment before ordering – safety above all! To ensure a successful repair and maintain the longevity of the device, it is mandatory to use only original parts. Non-original parts may cause damage and void the warranty. Now click the 'Check Model Compatibility' button at the top of the page and our system will immediately confirm that the part is suitable for you.

What supports the freezer drawer from below?

The support rod supports the freezer drawer – it is the component that connects the bottom of the drawer front panel to the left slide rail. Without this support, the left side of the drawer sags, friction is created, and the drawer does not open straight. The rod carries some of the weight of the loaded drawer with each opening and closing – ensuring smooth and balanced movement. Without this support, all the stress is transferred to the rails and panel, which accelerates their rate of wear.

What are the signs that the support rod is broken?

Three clear signs indicate part failure:

✅ The drawer leans to the left – the left side drops when fully opened ✅ New friction sound – the drawer “drags” on the plastic instead of sliding smoothly ✅ The front panel is not straight – you can see an uneven gap between the refrigerator door and the drawer panel

From the experience of our technicians, a drawer that tilts to the left and is left that way also damages the slide rail within a few weeks. The cost of repairing the rail is 3 times higher than replacing the support rod alone. It is better to replace it early.

📋 Technical specifications

✅ Compatible models

The part is suitable for Liebherr K and KB series models (make sure it matches the E-Nr number on the device sticker):

• K series (refrigerators)
• KB series (built-in refrigerators)

E-Nr sticker location: On the left inner wall of the refrigerator, visible after removing the vegetable drawer.

🔧 How do you replace the lower support rod?

Replacing the support rod is a low-difficulty operation that does not require tools. It takes about 5-10 minutes. There is no need to disconnect the device from the power supply.

1. Open the freezer drawer completely. And we emptied its contents
2. Lift the drawer off the rails. – Lean forward slightly and pull upwards
3. Locate the left support rod. At the bottom of the drawer – it is usually held in place by two tabs
4. Click on the locking tabs And release the broken rod
5. Insert the new rod. Until you hear a clear “click”
6. Put the drawer back into the rails. And check that it slides straight.

⚠️ Please note: Make sure the rod is properly locked before putting the drawer back in. A rod that is not properly locked will pop out again upon first use.

💡 Tip from the experts

What most people don’t know: In our technicians’ experience, 70% of support rods break due to unbalanced loads – not because the part is old. When all the heavy meat is concentrated on one side of the drawer, the left side takes on double the load. Evenly distributing heavy products between both sides of the drawer extends the life of the part by years. A simple 30-second tip for each filling.

❓ Frequently Asked Questions

Does the right support rod also need to be replaced at the same time?

It is not mandatory, but it is recommended to check it. The left and right rods work under similar loads. If the left one breaks after several years of use, the right one is worn out accordingly. Check if it is held firmly by its tabs, and if there are small cracks, replace it immediately as well.

Will a drawer that tilts also damage the rails?

Yes. A drawer that tilts to the left creates uneven friction on both rails. The left rail takes on more stress than originally designed. In our experience, 3-4 weeks of neglect after a rod break is enough to damage the rail – and the cost of repairing it is significantly higher than replacing the rod alone.

Will a non-original part also fit?

Non-genuine parts often do not meet the exact plastic standard that Behar defines for a freezer environment. At temperatures below -18, inferior plastic becomes brittle faster and may not connect securely to the front panel. A genuine part with part number 7432348 ensures full fit and durability for years.