Description

Original detergent drawer cover for Miele washing machine Miele 12686200

The original Miele 12686200 detergent drawer cover (Miele) is the correct replacement part for repairing the detergent drawer in a W1 series washing machine, model WDB020. The part is made of durable plastic, fits exactly into the drawer slot, and restores the functionality of the CapDosing mechanism to perfection. A simple do-it-yourself replacement that takes about 10 minutes without tools.

Is the lid broken? This is the part you need. The soap drawer lid is one of the most damaged plastic parts in a washing machine – it opens and closes with every wash cycle, and one small crack is enough for the drawer to stop closing properly. When this happens, the detergent doesn’t reach the drum at the right time, and the result is less clean laundry and sometimes detergent residue in the drawer.

A moment before ordering – safety above all! To ensure a successful repair and maintain the longevity of the device, it is mandatory to use only original parts. Non-original parts may cause damage to the device. Now click the 'Check Model Compatibility' button at the top of the page and our system will immediately confirm that the part is suitable for you.

What causes the soap drawer lid to break?

The soap drawer lid usually breaks from a sharp blow – opening it with a hand that hits the cabinet door, or closing the drawer too hard. Natural wear and tear over the years also causes the plastic hinge to break at a fixed point. In the experience of our technicians, most drawer malfunctions are resolved by replacing the cover only – without the need to replace the entire drawer.

The original Miele cover is made of the same flexible polypropylene as the original cover that came with the appliance. It withstands the heat and humidity of the drawer compartment, and attaches to the drawer body with a single click. ✅ A non-genuine part often does not fit exactly and will cause the drawer to sag or not close properly.

Where is the model number sticker? On a Miele WDB020 washing machine, the E-Nr sticker is usually located inside the appliance door, on the inner frame. Look for a number that starts with WDB.

Why original cover and not a replacement?

⚠️ Non-genuine soap drawer parts look similar but often differ by 1-2 mm at the hinge points. A small difference that causes the drawer to not close at all, or to close crookedly. In our experience, about 40% of customers who purchased a replacement returned to purchase the original part – and the second time they already knew.

The original cover 12686200 comes directly from the manufacturer, and is guaranteed to fit perfectly with the WDB020 drawer body and Miele's unique CapDosing mechanism.

📋 Technical specifications

✅ Compatible models

The part is definitely suitable for the following model (check against the E-Nr number on the sticker):

• Miele WDB020 – W1 front loading washing machine 7 kg

⚠️ For compatibility with additional models – use the compatibility check button at the top of the page or contact customer service.

🔧 How do you replace the soap drawer cover?

Replacing the drawer cover is a simple, low-difficulty DIY job – no tools required, and takes about 5 to 10 minutes. Unplug the appliance before starting work.

Replacement steps:

1. ⚠️ Make sure the machine is not in operation.
2. Pull the soap drawer all the way out and press the inner release tab – remove the entire drawer.
3. Loosen the old cover: Press both side tabs at the same time and pull up.
4. Insert the new cover: Align it over the drawer body and press down until it clicks into place.
5. Put the drawer back in and check that it closes easily and straight.
6. Plug in and run a short test cycle.

💡 Tip: Before putting the drawer back in, take the opportunity to clean the drawer compartment with warm water and a brush – powder residue accumulates there and can cause blockages.

💡 Tip from the experts

From our technicians’ experience: The number one reason why a soap drawer won’t drain properly isn’t necessarily a broken lid – sometimes the problem is a clogged siphon inside the drawer. Before ordering a part, remove the drawer and check that the small siphon in the drawer moves freely. In 30% of cases that come to us with a “drawer not working” – the problem is just a clogged siphon , a 3-minute cleaning solves everything without the need for a new part.

❓ Frequently Asked Questions

Is the Miele WDB020 soap drawer cover also suitable for other models?

Part number 12686200 is approved for the WDB020 model. Other Miele W1 series models may use a slightly different cover design. Before ordering a different model, please enter your E-Nr to check compatibility - a change of one year of manufacture can change the part code.

Is it possible to replace the cover without calling a technician?

Yes. This is one of the easiest parts to replace yourself. No tools are required, no need to open the back of the appliance. The entire operation is done through the drawer itself in about 5 minutes. It is only important to make sure that the machine is not in operation before starting.

The cover is stiff and doesn't close like it used to - what do we do?

If the cover is intact but difficult to close, the cause is usually a buildup of hardened powder on the hinge. First, try cleaning the hinge points with an old brush and warm water. If the problem persists, the plastic inside is probably cracked – then it needs to be replaced.