Description

Pair of original carbon brush holders for Miele washing machine motor Miele 4297410

The Miele 4297410 Carbon Brush Holder Pair is the part that allows your washing machine motor to work properly. The set includes two complete holders with carbon brushes, and is suitable for Miele washing machines from the W700, W800 and W900 series, as well as dozens of other models. The part ensures stable electrical contact with the motor cylinder, preventing recurring faults and returning the appliance to full operation. SKU: 4297410 (also includes 4297411, 4297412, 4297413, 4297414).

The washing machine is not spinning? The drum reaches a low speed and stops? About 65% of these faults are directly due to wear of the carbon brushes in the motor. The carbon brushes are a consumable component – ​​they wear out over years of use and lose contact with the motor cylinder. The result: a weak motor, intermittent running, and finally a complete stop of rotation.

Before you order: To ensure a successful repair, it's important to make sure the part fits your exact device model. Click the 'Check Model Compatibility' button at the top of the page for instant verification.

What happens when the carbon brushes wear out?

The washing machine motor operates using direct contact between the carbon brushes and the rotating metal cylinder in the motor. When the brushes become short and lose contact, the motor receives less current, overheats, and loses power. Common signs include: the drum spinning slowly and without power, a slight burning smell during washing, unusual noises from the motor, or a drum that reaches the spin speed but does not reach maximum speed.

From the experience of our technicians, in the W800 – W900 series models, the carbon brushes reach the wear limit after about 8-10 years of intensive use. Timely replacement prevents damage to the engine cylinder, the repair of which is three times more expensive than replacing the brushes alone.

Why choose a part that matches the original part number?

Parts that do not exactly match the specifications of Part Number 4297410 may damage the metal cylinder of the engine. The brushes operate at a specific pressure and at a precise angle - a part with different dimensions will produce sparks, excessive wear and irreparable damage to the engine.

✅ The set includes two holders complete with carbon brushes

✅ Dimensions: 15 × 5 × 29.5 mm, AMP connector with a diameter of 4.8 mm

✅ Compatible with Miele combined washing machines and clothes dryers

✅ Can be self-installed – no special tools required

📋 Technical specifications

✅ Compatible series

The part is suitable for all models of the following series:

• W700 series (W7xx)
• W800 series (W8xx)
• W900 series (W9xx)

⚠️ Please note: The model sticker (E-Nr) on Miele washing machines is usually located on the inside of the appliance door. Please make sure your model belongs to one of the above series before ordering.

🔧 Can I replace the carbon brushes myself?

Replacing the carbon brushes requires disassembling internal parts of the device and working near electrical components. It is recommended that a qualified technician perform the replacement. Improper installation may cause further damage to the motor.

⚠️ If you choose to perform the replacement yourself – completely unplug the washing machine before any action.

Replacement steps:

1. Move the washing machine away from the wall and access the back or side panel (depending on the model).
2. Remove the panel cover (2-4 screws).
3. Locate the device's motor - the holders sit on the sides of the motor and are connected to a small electrical plug.
4. Disconnect the electrical connection plugs from the old brush holders.
5. Loosen the old holders – they are usually held in place with light pressure.
6. Insert the new holders into place until they lock.
7. Reconnect the electrical plugs and make sure the connection is secure.
8. Assemble the panel and perform a test run.

💡 Tip from the experts

From the experience of our technicians, about 30% of customers who replaced carbon brushes found that the motor roller was slightly worn. Before installation, check that the roller surface is smooth and uniform. If there are deep dents or grooves, a light cleaning with fine sandpaper (400 grit) will improve the contact quality and extend the life of the new brushes by at least a year or two. A 3-minute operation that can prevent a repeat failure.

❓ Frequently Asked Questions

What are the signs that the carbon brushes in the washing machine need replacing?

The most common signs: the drum spins slowly or stops before reaching the spin speed, the spin is weak and does not reach maximum speed, there are slight sparks from the motor, or a slight burning smell during washing. If you notice any of these signs – checking the carbon brushes is the first step.

Can only one brush be replaced?

It is recommended to replace both brushes together, even if only one appears worn. Carbon brushes wear out at a similar rate – an old brush together with a new one creates an imbalance in pressure on the engine cylinder and accelerates the wear of the new brush. Set 4297410 comes with two complete holders for exactly this purpose.

How long does the replacement take?

Replacement takes between 20 and 30 minutes by a qualified technician. The technician accesses the engine through the rear or side panel, depending on the model.