Description

Miele Dishwasher Upper Protection Panel Miele 10794031

The top protection panel 10794031 is a genuine Miele flexible plastic film, which is attached to the underside of the worktop above the dishwasher. It protects the surface from moisture penetration and steam emitted whenever the door is opened. The part is suitable for Miele dishwashers G 4xxx, G 5xxx (models from 2020 onwards) and G 7xxx series, and is supplied as a genuine OEM part with manufacturer part number 10794031.

Your kitchen is meticulously designed – but every time you open the dishwasher door, steam and moisture are inadvertently sent directly to the underside of the countertop. Over time, the damage builds up: swelling, peeling, stains – especially on wood, Corian, or white countertops. The original Miele protection panel sits right there and absorbs the moisture – so the surface remains intact.

Click the 'Check Model Compatibility' button above for a quick verification of your dishwasher model.

What happens to the work surface without protection?

Every time you open the dishwasher door at the end of a hot wash program, a small column of steam rises – invisible, but active. It reaches directly to the underside of the worktop. Without a protective layer, the moisture penetrates the material over time.

Engineered marble and wood: Moisture causes the finish to swell and peel. Corian and laminate: Repeated exposure to moisture weakens the seal and creates stains. White marble: Yellowing and permanent marks that cannot be removed with regular cleaning.

The Miele Protection Panel stops this cycle of damage. It is glued precisely to the affected area, creating a continuous barrier.

All original Miele spare parts and accessories are available from us – OEM parts with factory-precise performance.

Original vs. Unapproved Replacement – ​​What's the Difference?

📋 Technical specifications

✅ Compatible models

The part is suitable for the following series (verify exact compatibility by your device model number):

G 4xxx series: All Miele dishwashers in this series. G 5xxx series: Models from 2020 onwards. G 7xxx series: All Miele dishwashers in this series.

How do you locate the model? The model sticker (E-Nr) is located on the edge of the inner door – visible when opening the dishwasher.

🔧 How do you replace the protection panel?

The replacement is simple and does not require professional tools – just patience and clean hands.

⚠️ No need to disconnect the power - this is just replacing adhesive tape, without touching electrical components.

Step 1 – Remove the old panel: Pull the old film at a low angle and slowly. If it is stuck tightly – use a thin plastic (old card) to lift the edge.

Step 2 – Clean the surface: Clean the top panel of the dishwasher of any remaining adhesive paper, grease and dust. The surface must be completely dry before gluing.

Step 3 – Attach the new panel: Place the panel at one end and press down evenly along the entire length. Use an old card to remove air bubbles – each bubble is a potential moisture infiltration point.

Step 4 – Stabilization: Wait about an hour before turning on the dishwasher for the first time, so that the adhesive can stabilize.

Prefer an expert to handle it? Our service team is available to coordinate a professional installation – contact us.

💡 Tip from the experts

From the experience of Daniel, our Miele dishwasher service expert: The most common damage to the countertop above a dishwasher occurs precisely after short wash programs – because the door opens with a lot of pressurized steam in a short period of time. Long, hot programs end with a drying phase that reduces moisture. Therefore, if you use a lot of quick programs – this panel is even more important.

❓ Frequently Asked Questions

Is the protective panel also suitable for an older Miele dishwasher?

No – Part 10794031 is for G 4xxx, G 5xxx from 2020, and G 7xxx series only. Older models have a different panel. Check the model number on the E-Nr sticker inside the door and verify compatibility before ordering.

Can the panel be replaced by yourself, or do I need a technician?

The replacement is completely simple and does not require tools. Remove the old panel, clean the surface, and stick the new one. All the tools for replacement – ​​a clean hand and an old card for wiping. No need to disconnect the power.

Why should you choose an original Miele panel rather than a replacement?

The original panel comes in precisely measured dimensions according to the Miele factory, with an adhesive adapted to the heat and humidity of a working dishwasher. An unapproved replacement may not arrive in exact dimensions, lose adhesion prematurely, and allow moisture to penetrate even when it appears to be in good condition.

🚚 Shipping Information | ↩️ Transaction Cancellation and Returns