Description

Original door support for Whirlpool freezer 482000092616

The original Whirlpool door support 482000092616 is intended for the right side of the freezer door in GN and GVN series refrigerator-freezers. The part is made of cold- and abrasion-resistant plastic, ensuring a firm grip on the door and preventing spontaneous opening. Its dimensions: length 55 mm, height 23 mm, width 39 mm. Suitable for self-replacement without special tools.

Freezer door not closing properly? This is no small problem. Any unintentional opening of the freezer door allows warm air to enter , which affects cooling efficiency, increases electricity consumption, and can cause food to defrost. The door support is the small part that prevents all of this.

A moment before ordering – safety above all! To ensure a successful repair and maintain the longevity of the device, it is mandatory to use only original parts. Non-original parts may cause damage. Now click the 'Check Model Compatibility' button at the top of the page and our system will immediately confirm that the part is suitable for you.

What causes a door support to break?

The door support is exposed to dozens of openings and closings a day, to extreme temperatures, and to the weight of the door itself. Over time, the plastic loses flexibility, cracks, or breaks completely. The most obvious sign: the freezer door won't stay closed or opens on its own – even when you think you've closed it tightly.

In our technicians’ experience, this fault is usually only discovered when you notice water droplets on the floor next to the refrigerator, or when the compressor is running continuously without stopping. Both of these signs suggest that the freezer is “working hard” because it is losing cold – and a broken door support is one of the common causes.

📋 Technical specifications

✅ Compatible models

The part is suitable for the following models (make sure it matches the model number on the device sticker):

• GN5170 / GN5170M
• GN5180 / GN5180M
• GN5190 / GN5190M
• GN5210 / GN5210M
• GN5215M
• GVN5170 / GVN5170M
• GVN5180
• GVN5210 / GVN5210M
• GVN5215 / GVN5215M
• GV5170

Where to find the model number? On Whirlpool refrigerators, the model sticker is usually located on the inside wall of the refrigerator – usually on the left side, at eye level.

🔧 How do you replace the door support?

Replacing a door jamb is a simple DIY task that takes about 5 minutes and requires no tools. Difficulty level: Very easy.

⚠️ Before you begin: Unplug the refrigerator.

1. Open the freezer door for easy access to the right bracket.
2. Locate the old door support – it sits on the right side of the door frame.
3. Loosen the old support (usually by pressing/slightly shifting - without screws).
4. Insert the new support into the same location until you hear a “click.”
5. Reconnect the power and check that the door closes and opens properly.

💡 Tip from the experts

From the experience of our technicians, about 40% of customers who replaced a door support saw a decrease in electricity consumption on the next bill – most do not realize how much energy the freezer “burns” when the door is not completely sealed. Before checking for compatibility, it is also worth checking the door seal: if it is hard, cracked, or does not shrink properly – it may also need replacing. Two actions together save an expensive service call later.

❓ Frequently Asked Questions

Does the door support fit the left side as well?

No. SKU 482000092616 is for the right side only. There is a separate SKU for the left side. Verify the required side before ordering – the easiest way to check is by locating the problem: where the door does not close.

The door opens by itself – is it safe to continue using the refrigerator?

It is recommended to address this as soon as possible. A loose freezer door causes the compressor to run continuously, which shortens the life of the appliance and increases your electricity bill. In the meantime, you can place a light object near the door as a temporary solution – but replacing the support is the final solution.

Does the replacement require a technician?

No. This is a DIY part – extremely simple. No tools, no screws, and no additional disassembly required. Most of our customers report a replacement in less than 5 minutes.