Description

Original Whirlpool washing machine drum agitator 480111104175

Original Whirlpool agitator, part number 480111104175, 240 mm long. The part is mounted on the inner wall of the machine drum, lifts and drops the laundry during washing, and ensures water and detergent penetrate the fabric fibers. Suitable for Whirlpool AWOE and WFE models, and is designed for direct independent replacement without special tools.

Have you heard knocking noises from your machine? The agitator is broken – and replacing it is easier than you think. The machine continues to work even with a broken or missing agitator, but the laundry comes out less clean and the clothes may be damaged. Check your model compatibility below and complete the repair today.

Why does the laundry come out dirty even after a full cycle?

A broken or missing agitator is the most common cause of this complaint. Without the agitator, the clothes lie at the bottom of the drum and do not undergo the lifting and dropping process that ensures even contact with the water and detergent.

The agitator works on three levels simultaneously: it lifts the clothes up as the drum spins, distributes the soapy water throughout the load, and balances the load of wet clothes – which reduces shock and preserves the machine’s bearings over time. The original Whirlpool agitator is made of hardened plastic with precise locking clips to the drum wall – unlike non-original parts that sometimes loosen after several wash cycles.

In our technicians' experience, about 65% of customers who reported "knocking noises from the machine" found a broken or loose agitator - and the replacement completely solved the problem in less than 20 minutes.

📋 Technical specifications

✅ Compatible models

Verified models:

• AWOE8558
• WFE1070BD
• WFE1075BD

Compatible series: AWOE, WFE

⚠️ Before ordering: Find the model sticker (E-Nr) on the inside of the machine door and make sure your model is listed. If you are not sure – contact us before ordering.

🔧 How do you replace an agitator in a Whirlpool washing machine?

Replacing the agitator is a simple DIY repair that takes 10-15 minutes and requires no tools. There is no need to disassemble the machine.

Replacement steps:

1. Turn off the machine. and unplug before starting work
2. Open the drum door. For easy access to the inner wall
3. Press the locking latches of the old stirrer (usually two) and pulled it out
4. Insert the new stirrer. into the grooves in the drum wall and press until you hear a click.
5. Check stability – The stirrer should not move at all after assembly.
6. Run a short cycle For testing before full use

💡 Tip: If you have three agitators in the drum – replace them all together. The cost of agitators is low, and if one breaks, the others are probably at a similar stage of wear.

💡 Tip from the experts

Check the condition of the agitators once a year – especially if you wash a lot of jeans, towels or heavy children’s items. Press down on each agitator with your finger: if it wobbles – the clip is loose and should be replaced before it falls into the drum and damages the clothes.

The common mistake we see over and over again: a customer continues to wash with a missing agitator because the machine “works fine.” In reality, the laundry spins unevenly, the delicates get tangled, and the fabric fibers wear out faster. Three complete agitators in the drum = better cleaning + longer life for the clothes.

❓ Frequently Asked Questions

What is the difference between an original mixer and a non-original one?

A genuine Whirlpool agitator is manufactured to the exact dimensions of the specific drum and undergoes quality testing by the manufacturer. Unapproved parts are made of plastic that is not resistant to heat and detergents, and sometimes come loose from the drum after a few weeks. Replacing it again negates the initial “savings.”

Can I continue washing with a broken agitator?

The machine will continue to operate, but there are two risks: First, plastic fragments can get stuck in the seal sleeve and cause a leak. Second, washing in an unbalanced drum accelerates wear on the machine's bearings - a much more expensive repair than a new agitator. We recommend replacing as soon as possible.

How many agitators are there in the drum?

Typically, three agitators are evenly distributed on the drum wall. When one agitator breaks, the two seemingly intact ones will still “work” – but the balance is not perfect. For optimal results and to prevent noise, it is recommended to check the condition of all three agitators and replace them in pairs.