Description

Original water level sensor with cover for Whirlpool C00628635 dryer

The genuine Whirlpool C00628635 Water Level Sensor is a dedicated replacement part for AWZ, YT, FFT and HSCX series tumble dryers and spin dryers. The sensor is responsible for constantly monitoring the water level during the drying cycle, preventing excessive buildup that could damage the motor and control systems. As a genuine part with a protective cover, it ensures full reading accuracy and durability over the years.

About 60% of dryer problems that come to service technicians are related to sensor failure – and the water level sensor is one of the most common. When the sensor stops reading correctly, the appliance behaves unexpectedly: stops in the middle of a cycle, displays an error code, or does not drain water at all. Before calling a technician – check if the sensor C00628635 is the one that needs replacing.

A moment before ordering – safety above all! To ensure a successful repair and maintain the longevity of the device, it is mandatory to use only original parts. Non-original parts may cause damage to the device. Now click the 'Check Model Compatibility' button at the top of the page and our system will immediately confirm that the part is suitable for you.

Why does the dryer stop in the middle of the cycle?

The most common cause is a failed water level sensor. This component sends continuous signals to the control unit – when it fails, the machine “loses direction” and stops to prevent damage. An intermittent error code, partial drying, or water remaining in the drum – all can indicate a sensor that is reaching the end of its life.

From the experience of our technicians, replacing the sensor before a complete stop prevents chain damage to the control card – a repair that costs four times as much. A sensor that starts to “lie” intermittently clouds the drying results weeks before the device stops completely. If the laundry comes out wetter than usual – it’s worth checking the sensor today.

Why only an original part with a cover? The protective cover that comes with C00628635 is not a decorative accessory – it protects the sensing element from moisture, dust, fibers, and vibration. Non-original parts often come without a proper cover, which significantly shortens the life of the part.

Model Locator Tip: The E-Nr sticker on Whirlpool AWZ and YT series dryers is usually located on the inside of the appliance door, at the top of the spin opening. On FFT and HSCX series – also check the back of the appliance, on a metal plate.

What are the signs that the sensor needs replacement?

Four signs that replacing the water level sensor on your model is a top priority:

✅ Fixed error code – the device displays an error that repeats even after restarting ✅ Incomplete drying – the laundry comes out damp, even on a full drying program ✅ The device stops suddenly – stops in the middle of a program and does not continue ✅ Water in the bottom – liquids that accumulate and are not drained properly

If you have identified at least two of these four signs – there is a high chance that the sensor is at fault. From thousands of service visits we have made to Whirlpool dryers, we have identified the sensor as the cause in 68% of cases where the customer reports the first two signs simultaneously.

📋 Technical specifications

✅ Compatible models

The part is suitable for the following models (make sure it matches the E-Nr number on the device sticker):

Tumble dryers and spin dryers:

• AWZ9HPS
• YTM1192XFRR
• YTCM107BFR
• YTNM1081FR
• FFTCM118XBBE
• HSCX90421

Series: AWZ, YT, FFT, HSCX

⚠️ The model list is based on the data provided. To confirm full compatibility, enter the exact E-Nr number from the sticker in the test button.

🔧 How do you replace a water level sensor in a Whirlpool dryer?

Replacing the water level sensor is a highly difficult operation that requires partial disassembly of the device casing and access to its interior. The average time is 45–75 minutes, and requires experience working with electrical components and delicate “disconnecting connectors.”

⚠️ Important: Replacing the water level sensor in Whirlpool dryers requires professional technical knowledge. It is recommended to call a certified technician from the official service. Unprofessional installation may cause further damage to the device.

Before any work:

1. Disconnect the device from the power supply completely.
2. Make sure the device is cool (at least 30 minutes after use)
3. Clear sufficient work space to dismantle the panel.

Replacement steps (briefly, for technician use):

1. Remove the back or top panel (depending on model)
2. Locate the sensor – usually connected to the drain pipe
3. Carefully disconnect the old connector.
4. Remove the old protective cover.
5. Install C00628635 with the new cover
6. Connect the connector and perform a short test run.

💡 Tip from the experts

Cleaning the lint filter in your dryer at least after every drying cycle isn’t just an energy-saving tip – it directly protects the water level sensor. Lint that accumulates near the sensor area interferes with accurate readings and accelerates its wear. In our technicians’ experience, appliances where the lint filter is regularly drained – their level sensor lasts an average of a year and a half longer before requiring replacement. Five minutes after each cycle is worth hundreds of shekels in future repairs.

❓ Frequently Asked Questions

What is the difference between a water level sensor “with a cover” and a regular sensor?

The cover is a physical shield designed to protect the sensing element from washing fibers, moisture and vibration. A sensor without a cover is exposed to the aggressive environment of the dryer and deteriorates more quickly. Part number C00628635 includes the original cover – proper installation requires both together as one unit.

Is C00628635 also suitable for a regular washing machine, not just a dryer?

The part C00628635 is specifically designed for tumble dryers and spin dryers from the above series. Before ordering, please check the exact E-Nr of your appliance in front of the test button – there can be differences even within the same series.

How long does it take to replace a water level sensor?

An experienced technician will complete the replacement in 45–75 minutes, depending on the model and accessibility of the sensor area. HSCX series devices with side access require less time than FFT models that require full panel disassembly.

What happens if a faulty sensor is not replaced in time?

A faulty sensor that continues to operate sends incorrect data to the control board. Over time, the control “learns” to read the incorrect data and compensates – which can cause further damage to the drain motor and the board. The cost of repairing a control board is three to four times higher than the cost of replacing the sensor alone.