Description
The original feed tube 05797290 transfers water from the pump to the middle spray arm (spray arm) under the upper basket in the dishwasher. The part is made of durable plastic, dimensions 48×98×270 mm. It fits Miele G601 to G858 series - models without upper cutlery tray (Non SC). This is a genuine Miele OEM part, part number 05797290.
Are the dishes in the upper basket not coming out clean? Is the middle sprayer not rotating? The most common cause is the feed tube – cracked, broken, or disconnected. Once the tube fails, water doesn’t reach the middle sprayer at all. Result: an upper basket that doesn’t clean properly.
Just before ordering – safety above all! It is mandatory to use only original parts. Non-original parts may cause damage. Click the 'Check Model Compatibility' button at the top of the page – the system will immediately confirm that the part is suitable for your model.
Why is the middle sprinkler not functioning?
The middle spray arm is completely dependent on the feed tube. The tube runs from the pump along the back of the dishwasher, ending at a connection to the spray arm below the top rack. When it cracks—usually from wear and tear, a dropped dish, or careless removal—the water pressure drops. The middle spray arm stops rotating, and the top rack doesn’t clean.
Miele dishwashers G601-G858 series are equipped with two baskets and three spray arms: lower, middle and upper. The middle spray arm sits between the two baskets and is completely suspended from the 05797290 hose. Therefore, hose failure only affects the upper compartment – not the lower one.
It is important to locate the model number before ordering. The sticker is located on the inside lip of the dishwasher door, on the top or side.
Looking for SKU 5797290?
This is the exact same part – the official Miele format includes the number 0 at the beginning: 05797290. You can order with complete confidence.
For more information about Miele dishwashers and genuine spare parts, visit our Miele page.
Original vs. Unapproved Replacement – What's the Difference?
| parameter | Original part (OEM) | Unapproved replacement |
|---|---|---|
| Connection compatibility | Accurate to the model | Not guaranteed |
| Heat and pressure resistance | Tested to Miele standard | Not verified |
| Inner diameter | Compatible with pump pressure | May cause a drop in blood pressure |
| Product life | Full | Accelerated wear |
📋 Technical specifications
| attribute | value |
|---|---|
| Manufacturer's SKU | 05797290 |
| Additional SKU | 5797290 |
| brand | Honey |
| Brand + MPN | Honey 05797290 |
| 48×98×270 mm | |
| material | Plastic |
| compatibility | G601 to G858 series (Non SC) |
| Installation level | DIY of medium difficulty – basic experience required |
✅ Compatible models
The part fits Miele dishwashers from the G601 to G858 series - models without an upper cutlery tray (Non SC). Check compatibility by checking the model number on the door sticker.
G6xx series: G601, G602, G640, G641, G660, G680 and more in the series G7xx series: G700, G720, G740, G760, G780, G790 and more in the series G8xx series: G800, G820, G840, G850, G858 and more in the series
To check for exact compatibility – enter the full model number in the check button at the top of the page.
🔧 How do you replace the supply hose for the middle sprinkler?
Replacing the hose is a moderately difficult DIY job. The hose is attached at several points along the back of the wall – each must be loosened individually. Tools required: Phillips screwdriver and flathead screwdriver.
⚠️ Before any work: Turn off the dishwasher and unplug it.
- Empty the laundry compartment. – Remove the two baskets.
- Locate the pipe. – It goes up along the back wall, connected to several anchor points.
- Loosen the top connection. – The hose connects to the middle sprinkler from above. Gently loosen with a flat screwdriver.
- Release the middle anchor points. – Carefully release each clip along the side.
- Loosen the lower connection. – The hose sits in a bracket near the floor of the dishwasher. Tilt downward to release.
- Insert the new pipe. – Connect from bottom to top in reverse order. Make sure each clip clicks into place.
- Run a short cycle – Check that there are no leaks along all connection points.
Prefer an expert to install? Our service team is available to coordinate a professional installation.
💡 Tip from the experts
In the experience of our Miele service technicians, the hose is most often damaged due to careless removal of the upper basket. Pulling with excessive force damages the hose's connection points. Each time you remove a basket - lift it slightly and pull it straight out. A simple operation that saves repair.
Daniel – Miele Dishwasher Expert
❓ Frequently Asked Questions
Why doesn't only the top basket get cleaned?
When the middle sprinkler fails, the lower basket continues to receive water from the lower sprinkler. Therefore, the lower one is clean and the upper one is dirty. This is the classic sign of a failure in the feed tube 05797290 – or in the middle sprinkler itself.
Can I replace the pipe myself?
It is possible, but it is a moderately difficult DIY. The pipe is connected at several points along the back of the wall, and each one must be loosened individually with a flat screwdriver. Anyone familiar with plastic work and clip mechanisms will be fine. Anyone who is unsure is better off calling a technician.
Is 05797290 compatible with Miele models with a top cutlery tray?
No. The part is for models without a top cutlery tray (Non SC). SC models use a different feed tube. Check the model number on the door sticker – if it includes “SC” – it is a different model.
🚚 Shipping Information | ↩️ Transaction Cancellation and Returns













