Description

Genuine Whirlpool Dishwasher Water Sprayer Valve Kit C00525113

The Whirlpool C00525113 3-Way Valve Kit is responsible for routing water between the dishwasher's spray arms. Unlike a pump that pushes the water, this valve decides where it goes – to the top or bottom spray arm – ensuring that all racks are cleaned properly. The kit includes: a valve, a small motor that turns it, and an O-ring seal. Manufacturer Part Number: C00525113 / 488000525113. Due to the complexity of the installation, it is recommended that a qualified technician be used.

Why does the valve determine whether the dishes come out clean?

The valve's job is simple: to receive water from the pump and direct it to the correct sprinkler at each stage. When it breaks, the top or bottom sprinkler stops receiving water – and the dishes in one basket come out dirty while the other basket is completely clean.

The sign that identifies this malfunction: The dishwasher works, fills and drains normally – no error code, no loud noise – only one basket does not clean. The O-ring in the kit seals the valve against the pump body, and without it, the water “runs” inside and does not reach the sprinklers under pressure.

Just before ordering – it is mandatory to use only original parts. Non-original parts may cause damage. Click the 'Check Model Compatibility' button at the top of the page – the system will immediately confirm that the part is suitable for you.

What are the signs that the valve needs replacement?

✅ One basket does not clean – the top basket comes out clean but the bottom one does not, or vice versa

✅ A stopped sprinkler – one of the sprinklers does not rotate during flushing

✅ Uneven water pressure – one sprinkler sprays strongly and the other hardly at all.

✅ Click-click – a slight rhythmic noise during flushing from the valve's small motor

⚠️ Before ordering a part – clean the filter at the bottom of the dishwasher. From the experience of our technicians, in 25% of cases the clogged filter is the cause – a 5-minute operation that can save the entire replacement.

📋 Technical specifications

✅ Compatible models

The part is suitable for the following models (check compatibility with the E-Nr number on the dishwasher sticker):

Whirlpool / Bauknecht:

• ADG6500IX
• ADP931WH
• And other models from the ADG, ADP series

Indesit:

• LI6650
• LI6670
• LI6690
• LI6700
• LI6800
• and other models from the LI series

⚠️ The model sticker (E-Nr) is located on the top or side edge of the dishwasher door - discover it by opening the door completely.

🔧 How do you replace the valve kit?

This is a complex job: you have to disassemble the pump system, disconnect electrical connections, and insert the new O-ring precisely. Labor time: 1 to 2 hours for an experienced technician. Inserting the O-ring incorrectly will cause an internal leak – the exact problem we wanted to solve.

⚠️ Important: Replacing a 3-way valve kit requires professional technical knowledge. It is recommended to call a qualified technician.

Replacement steps for a technician:

1. Unplug the dishwasher and turn off the water tap.
2. Take out the baskets and remove the lower sprinklers.
3. Remove the filter cover and the drain reservoir.
4. Loosen the screws holding the pump assembly.
5. Disconnect the electrical connections from the small valve motor.
6. Remove the old valve and remove the O-ring.
7. Insert the new O-ring precisely – without twisting.
8. Insert the new kit and connect the electrical connections.
9. Assemble the lid, filter, and sprinklers.
10. Run a test cycle and check that all sprinklers are operational.

💡 Tip from the experts

In the experience of our technicians, the most common cause of premature failure of this valve is limescale. Hard water – common in 80% of homes in Israel – builds up limescale on the O-ring and the valve’s rotating shaft, until it cannot rotate. Regularly refilling the dishwasher with salt and anti-limescale agent extends the life of the valve by two to three years – a 30-second operation per month that saves hundreds of shekels in repairs.

❓ Frequently Asked Questions

Why is the top basket clean but the bottom one isn't – or vice versa?

This is the classic sign of a failed 3-way valve. When the little motor fails, the valve sticks in one direction and only feeds some of the sprinklers. The pump is working fine – the water just isn’t getting to the right destination. Replacing the C00525113 kit restores water distribution to all sprinklers.

What is the difference between an original kit C00525113 and a non-original part?

A genuine kit comes with an O-ring that is precisely matched to the valve dimensions. A non-genuine part with an incorrectly sized O-ring will cause internal leakage and a drop in water pressure – the very problem we wanted to solve in the first place.

Can the fault be detected before ordering?

Yes. Run a short rinse cycle and open the door after 3 minutes. Check if all sprinklers are rotating. One sprinkler stopped – valve problem. All sprinklers stopped – main pump problem. Kit C00525113 solves the first case.