Description

Sauter Genuine Oven Door Frame Strip 8057265

The original Sauter 8057265 oven door frame strip is an upper strip located on the oven door and connects the door glass to the body of the appliance. The part is suitable for Sauter ovens from the 608 series and solves the problem of a frame that has cracked, separated from the door, or been damaged by heat. The original part ensures a precise fit to the door grooves, easy cleaning, and proper sealing of the glass.

Is your frame cracked? Is the glass wobbling and not sitting securely? תקלה זו שכיחה מאוד בתנורים לאחר שנות שימוש – And the solution is to replace the frame strap only, without calling a technician. Independent replacement takes about 15 minutes with just a Phillips screwdriver.

A moment before ordering – safety above all! To ensure a successful repair and maintain the longevity of the device, it is mandatory to use only original parts. Non-original parts may cause damage. Now click the 'Check Model Compatibility' button at the top of the page and our system will immediately confirm that the part is suitable for you.

Why is the door frame damaged – and what do we do?

The oven door frame is exposed to various damages: heat accumulated over years of use, aggressive cleaning, and blows when opening and closing. In most cases, the damage first appears as a small crack in the corner and then as the glass loosens. Immediate replacement of the strip prevents the risk of the glass falling and breaking.

In our experience in servicing spare parts for sauter ovens, approximately 65% ​​of customer inquiries reporting “loose glass” are resolved by replacing the frame strip only – without any need to replace the expensive glass panel itself.

⚠️ Please note: If a crack also appears in the glass itself - contact a certified technician to fully inspect the oven door.

✅ Advantages of the original part:

• High temperature resistant material – does not deform under heat
• Exact fit for Sauter Series 608 door slots
• Prevents grease and steam from penetrating into the door cavity
• Gives the door a perfect, like-new look

📋 Technical specifications

✅ Compatible models

Make sure to match the full model number on the appliance sticker. Location of the sticker on the oven: Inner door frame – at the top of the oven opening, or on the back of the appliance.

תנורים ובקרים:

• EBC943000E, EBC12319E, EBC12324E
• EBC6111, EBC6111XB
• EBC6211, EBC6211XB
• EBC6421, EBC6421W, EBC6421XB
• EBC6541AA, EBC7551AA
• EBE6421L, EBE7421, EBE7421L, EBE8441

תנורים נוספים (מותגים תואמים):

• EBF641KR, EBF641TA
• EBF6521AA, EBF6541AA
• EBF65P01AA, EBF65P02AA
• EBF7541AA, EBF7941AA

Compatible series: EBC, EBE, EBF, EHC

🔧 How do you replace the door frame strip?

The replacement requires a low level of difficulty – basic DIY. You will need a Phillips screwdriver, about 15 minutes of free time, and thick gloves to protect your hands. It is recommended to perform the replacement when the oven is completely cold.

⚠️ Disconnect the oven from the power supply before starting work.

1. Open the oven door completely. And put a towel at the bottom of it
2. Locate the strap bolts. – Usually 2-4 screws along the top strap
3. Loosen the screws. Carefully and keep them.
4. Remove the old strap. – Pull gently upwards
5. Insert the new strap. into the grooves and straighten
6. Tighten the screws. Back – do not overtighten (plastic)
7. Open and close the door. To check that everything is in place correctly

💡 Tip from the experts

Based on dozens of service calls for sauter ovens, the problem that causes the earliest damage to the frame belt is cleaning with aggressive materials . Cleaning with strong solvents or steel wool damages the plastic and causes premature disintegration of the belt, often after only one to two years. To clean the belt – use only a damp rag with a little dish soap. A simple operation that extends the life of the part by more than doubles.

❓ Frequently Asked Questions

Can I replace the belt myself without a technician?

Yes, this is one of the easiest oven replacements. All you need is a Phillips screwdriver and 15 minutes. Unplug the oven, loosen 2-4 screws along the strip, remove the old one, and insert the new one. No special tools are needed and there is no safety hazard as long as the oven is cold and unplugged.

What is the difference between the original strap and a non-original part?

The original 8057265 strip is made of heat-resistant plastic that is precisely adapted to the door slots of the Sauter Series 608. Non-original parts may be made of cheap material that warps in high temperatures, will not sit exactly in place, and may loosen the glass after a short time. An original part guarantees both fit and safety.

The strap looks intact but the glass is still loose – what's the problem?

It’s likely that one of the internal clips that attach the strip to the door has broken. Check the screws along the length of the strip – if they connect to broken material, the entire strip will need to be replaced. If the screws are properly tightened but the glass still moves, the door itself may be warped and should be inspected by a technician.