Description

Original Sauter oven telescopic rail clip 8055997

The original Sauter 8055997 clip is a small but critical part of the oven's telescopic rail system. It secures the telescopic rail to the inner side rail, prevents movement when removing the pan, and serves as a safety mechanism that prevents the rail from detaching when fully opened. This original part ensures a precise fit for Sauter ovens and maintains safe use for years.

Does the telescopic rail slide but not stay in place? A worn retainer is the most common cause of this problem. The 8055997 retainer restores the fixation to its proper position – a stable rail, smooth extraction, and complete safety for every mold.

⚠️ Just before ordering – safety above all! To ensure a successful repair and maintain the longevity of the device, it is mandatory to use only original parts. Non-original parts may cause damage. Now click the 'Check Model Compatibility' button at the top of the page and our system will immediately confirm that the part is suitable for you.

What is the role of the gripper in the telescopic rail?

The telescopic rail consists of two parts: the rail itself and the side ladder that is attached to the side of the oven. The clip is the component that connects them – it “puts” the rail on the ladder and locks it in place. Without a proper clip, the rail wobbles, falls off when pulled out, or completely detaches from the ladder when fully opened. This is a real safety hazard – a hot, heavy pan falling out of the oven.

Another advantage of the clamp: it allows for complete modularity – the rails can be moved between the different heights of the ladder without tools, with just a light manual lift. When the clamp is worn, this movement becomes impossible or unsafe.

What are the signs that the catcher needs replacing?

✅ The telescopic rail wobbles or moves left and right while pulling out ✅ The template “wobbles” and does not come out straight ✅ The rail falls off the ladder when fully opened ✅ Difficulty moving the rail between ladder heights ✅ The clip appears cracked, broken or warped

When you detect one of these signs, replacing the clamp is the direct solution. In the experience of our technicians, most telescopic rail faults in sauter ovens are resolved by replacing the clamp alone – without an expensive service call.

🔍 Where is the sticker? The model sticker (E-Nr) on sauter ovens is located on the inner door lip or inside the oven frame. Open the door completely and examine the inside edge – there you will find the model number to verify compatibility.

📋 Technical specifications

✅ Compatible models

The part is suitable for the following models (make sure it matches the E-Nr number on the oven sticker):

Built in & Freestanding Ovens — CU / CI / SFB Series: CI810, CI910, CU800, CU900, SFB630, SFB640, SFB650, SFB680, SFB950, SFE630, SFE650, SFE950, SHB630, SHB640, SHE630

Built in & Freestanding Oven Pyrolytic: CU800P, CU900P, CI810P, CI910P, SFB950P, SFE950P, PYRO810, PYRO910, PYRO950

Built-in & Freestanding Ovens — D Series: D850, D860, D880, D890, D900, D950

🔧 How do you replace a clamp on a telescopic rail?

Replacing the clamp is a simple DIY operation that requires no tools at all. All you need is two hands and less than 5 minutes. There is no need to disconnect from the power supply – it is a completely mechanical plastic part with no contact with electrical systems.

Step 1: Remove the telescopic rail from the oven completely by lifting to the right from the ladder.

Step 2: Locate the old clip at the back or front of the track – it is a small plastic clip that is attached to the track body.

Step 3: Release the old retainer with a light push and pull. ✅ Do not force it – the part is designed to release easily.

Step 4: Put on the new retainer 8055997 until you hear a tangible click.

Step 5: Return the rail to the side ladder and check that it is stable and stays in place.

💡 Tip from the experts

From our technicians' experience, when one clamp breaks – the reason is usually an unbalanced load on the rail (heavy molds being pulled out at an angle). Before installation , check that the side ladder itself is straight and not warped – a new clamp on a crooked ladder will break again within weeks. A 10-second operation that saves another service call.

❓ Frequently Asked Questions

Do I need to buy two clamps – for each side?

The telescopic rail consists of a front clamp and a rear clamp – not on the left and right sides. Usually only one of them breaks. If only one clamp is damaged, it can be replaced separately. If both are worn – it is recommended to replace both at the same time to ensure full stability.

Is it possible to pull out the rail completely without breaking it?

Yes. Sauter telescopic rails are designed to be fully extended for cleaning and replacing parts. Lift the front up first, then pull out at an angle. If the rail does not move – the catch may be stuck and needs to be gently released before continuing.

Wouldn't a generic grabber provide the same service?

Genuine Sauter 8055997 clamp is made of high-heat-resistant plastic, precisely calibrated to Sauter's scale dimensions. A generic clamp may be too loose, too stiff, or not be able to support the load of the molds - and will fail during normal use. Risk: hot mold falling.