Description

Original fast gas burner head for Sauter stove AS0035214

Sauter AS0035214 Rapid Burner Head is the direct original part for repairing flame problems on TM and SPC series gas hobs. Diameter 140 mm, designed for the DC (large) burner – the most common failure on everyday cooking hobs. The part is made of cast iron resistant to extreme heat, and ensures uniform and full flame distribution as in a new appliance. Suitable for self-replacement by a qualified technician.

Is your flame uneven? Unstable ignition? From the experience of our technicians – 65% of cases where Sauter stoves exhibit a weak flame or uneven heat distribution, the problem is in the burner head itself and not in the gas valve. Replacing the original burner head solves the problem without an expensive service call.

A moment before ordering – safety above all! Gas stoves are a safety device. Use only original parts – non-original parts may cause uncontrolled gas dispersion and a fire hazard. Now click the 'Check Model Compatibility' button at the top of the page and our system will immediately confirm that the part is suitable for you.

Why isn't the burner distributing flame properly?

The burner head is the heart of the gas stove – it determines how many flames come out, in which direction, and with what intensity. When the burner head cracks, becomes clogged with cooking oil that seeps into the slots, or simply wears out from use – the flame becomes uneven, patchy, or goes out while cooking. Gas continues to flow but does not burn properly. This is an excellent self-repair fault with the help of an original burner head.

The DC (Double Crown / Rapid) is the largest burner on a stove, usually in one of the four positions. On Sauter’s TM and SPC series, the rapid burner comes in a diameter of 140 mm with a double flame spread – giving high power for rapid boiling and wok cooking.

📋 Technical specifications

✅ Compatible models

The part fits the following models. Check for compatibility by the full model number on the data sticker:

TM Series:

• TM0547E27

SPC series:

• SPC6632B
• SPC6631B

Where is the model sticker on the hob? On Sauter gas hobs, the data sticker is usually located on the hob frame – around the installation opening at the bottom, or on the side control panel. Have the model number ready before ordering.

🔧 How do you replace a gas burner head?

10 second replacement, no tools, no technician. The burner head simply sits on the burner base – no screws, no connections. All you have to do is:

1. Remove the pot support mesh.
2. Remove the burner dome (the top part).
3. Lift the old burner head.
4. Lower the new burner head AS0035214 to the same position.
5. Put the dome and net back on – and you're done.

💡 Tip from the experts

From our technicians’ experience – the most common cause of premature burner head failure is cooked oil that has seeped into the gas slots and burned there. A burner head that has burned inside acts like a damaged head – but cleaning will not help. Replacement is the only solution. Prevention tip: After any liquid cooking that has spilled, lift the dome and wipe the burner head to the side. 5 minutes of weekly cleaning will extend the life of the part by many years.

❓ Frequently Asked Questions

Can a gas burner head be replaced at home?

Absolutely – this is one of the easiest replacements on a gas stove. The burner head rests loosely on the base, without screws or tools. Lift, replace, put back. The entire process takes less than 10 seconds.

The flame comes out from only one side – is this because of the burner head?

Yes, this is the classic symptom of a burner head with clogged or damaged slots. When some of the gas slots are blocked, the gas only finds an outlet from one side – creating a one-sided, uneven flame.

How long does an original burner head last?

A genuine Sauter burner head will last for many years of daily use. Non-genuine heads, on the other hand, often come in a less durable alloy and can swell or wear out more quickly at high heat.