Description

Original middle inner glass for Sauter oven door 8051768

The original Sauter middle glass panel 8051768 is the central door component that separates the baking cavity from the outer glass layer. It is suitable for Sauter ovens from the ACV and SHV series in Israel, including models ACV20H30B, ACV20H30W, SHV631 and SHV632. Its precise dimensions of 464×404 mm, it is resistant to high heat, and ensures a perfect fit to the original door without the need for modifications.

Is the middle glass in the oven door broken? This is exactly the part you need. The middle panel is exposed to the highest heat in the door, and an unexpected hit from a pan or pot is enough to break it. Please note: replacing it requires complete disassembly of the oven door and careful work between three layers of glass – it is recommended that the replacement be performed by a qualified technician.

A moment before ordering – safety above all! To ensure a successful repair and maintain the longevity of the device, it is mandatory to use only original parts. Non-original parts may cause additional damage to the device. Now click the 'Check Model Compatibility' button at the top of the page and our system will immediately confirm that the part is suitable for you.

Why does the middle glass break – and how do you identify the problem?

The middle glass is the middle pane of the three layers of glass in a modern oven door. It sits between the outer and inner glass, absorbing intense heat transfer during every baking session. A sharp blow, a sudden extreme temperature change, or a crack that develops over the years can all cause it to break. The obvious sign: cracked or broken glass visible through the door.

Why not continue cooking with cracked glass? A crack in the middle glass impairs the door's insulating ability. Heat "escapes" to the outside - baking performance decreases, electricity consumption increases, and in severe cases, the glass may break inward.

✅ Cracked glass visible in the middle of the door ✅ Door warmer than usual outside even though the oven is closed ✅ Decreased baking results for no apparent reason

📋 Technical specifications

✅ Compatible models

The part fits the following models (make sure it matches the model number on the model sticker):

• ACV20H30B
• ACV20H30W
• SHV 631
• SHV 632

Where is the model sticker on a Sauter oven? On the door frame – on the inside of the oven frame, visible when the door is opened wide. The sticker contains the full model number and serial number.

🔧 How do you replace the middle glass in the oven door?

⚠️ Please note: Replacing the middle panel requires complete disassembly of the oven door – including careful removal of the outer glass layer and the inner glass layer, before the middle panel can be accessed at all. This is delicate work with three layers of glass at the same time, one of which may be broken and dangerous. We strongly recommend contacting a qualified technician to perform the replacement.

If you choose to do it yourself, you should work with thick gloves, in a clean environment, and with the utmost caution.

⚠️ First of all: Make sure the oven is turned off and completely cold.

1. Remove the oven door from the hinges and place it flat on a padded surface.
2. Loosen the screws holding the door frame – usually at the top and bottom.
3. Carefully remove the glass layer. The exterior and then the glass layer The inner
4. Now you can access the middle panel – remove it (note the direction – the inscription, if present, faces outwards)
5. Insert the new board 8051768 in exactly the same direction
6. Put the inner and outer glass layers back together, and assemble the frame – Do not overtighten.Tempered glass (glass that is resistant to heat and special pressure) may break if tightened too tightly.

💡 Tip from the experts

In our technicians’ experience, the most common mistake when replacing oven door glass is overtightening the screws during assembly. Tempered glass is resistant to extreme heat, but localized mechanical stress can cause it to break immediately – sometimes just a few days after installation. The rule of thumb: Tighten until the frame is stable, and stop. In 70% of the cases where we saw “new glass that broke quickly,” the reason was tightening it too tightly.

❓ Frequently Asked Questions

Can only the middle panel be replaced and not the entire door assembly?

Yes, on Sauter ACV and SHV series ovens, the oven door can be dismantled and each glass panel replaced individually. The middle panel 8051768 is a stand-alone part that can be replaced without purchasing the entire door assembly. This saves significant cost compared to a complete replacement.

Can a non-original part fit instead of 8051768?

Physically, a 464×404 mm board may “fit” – but non-genuine parts do not pass the manufacturer’s heat and pressure tests. Such a part may break prematurely and in extreme cases cause further damage. Genuine part 8051768 comes to exactly the same specifications as it left the factory.

How long does the replacement take and what tools are required?

An experienced technician can perform the replacement in approximately 30-60 minutes. Tools required: Phillips screwdriver, thick gloves to protect against glass shards, and a padded work surface to support the door. Since it requires complete disassembly of the door and handling of three layers of glass separately, it is recommended that the work be performed by a qualified technician.